Hp-Fehlercodes


ERROR-Code Beschreibung Optionen
Fehler 10.90.XY Patrone (Farbe) ersetzen

Fehler 10.90.XY Patrone (Farbe) ersetzen

Eine Farbpatrone hat das Ende ihrer Gebrauchsdauer erreicht und muss ersetzt werden.

Mögliche Maßnahme:

Ersetzen Sie die Farbpatrone.

 
Fehler 10.92.YY Patronen haben keinen Kontakt

Fehler 10.92.YY Patronen haben keinen Kontakt

Die Druckpatrone wurde nicht ordnungsgemäß in den Drucker eingesetzt

Mögliche Maßnahme:

Entfernen Sie die Druckpatrone, und setzen Sie sie erneut ein

 
Fehler 10.X.X Verbrauchtsmat.-Speicherfehler

Fehler 10.X.X Verbrauchtsmat.-Speicherfehler

Der Drucker kann in mindestens einem Druckpatronenspeichertag nicht lesen oder schreiben bzw. mindestens ein Speichertag fehlt. Die folgenden Meldungen des Bedienfeldes entsprechen der Farbe der Druckpatrone: 10.00.00 = Druckpatrone Schwarz / 10.00.01 = Druckpatrone Cyan / 10.00.02 = Druckpatrone Magenta / 10.00.03 = Druckpatrone Gelb

Mögliche Maßnahme:

1. Schalten Sie den Drucker aus und wieder ein. 2. Drücken Sie ? um weitere Informationen zu erhalten. 3. Sollte dieser Fehler weiterhin auftreten, wenden Sie sich an den HP Kundendienst.

 
Fehler 11.X int. Zeitfehler

Fehler 11.X int. Zeitfehler

Diese Nachricht wird angezeigt, wenn mit der Echtzeituhr auf der Formatierungskarte ein Problem aufgetreten ist. XX=01 Uhrbatterie leer / XX=02 Echtzeituhr defekt

Mögliche Maßnahme:

Drücken Sie Select-Taste um fortzufahren. Wenn dieser Fehler auftritt, fährt der Drucker damit fort, Datum und Uhrzeit anhand der Prozessoruhr aufzuzeichnen, bis er abgeschaltet wird. Solange dieser Fehler nicht behoben wird, werden Sie bei jedem Aus- und Einschalten des Druckers aufgefordert, Datum und Uhrzeit neu einzustellen.

 
Fehler 13.x Papierstau / Error 13.X Paper jam

Fehler 13.x Papierstau / Error 13.X Paper jam

Es ist entweder ein Papierstau im Drucker aufgetreten, oder das Papier staut sich in einem Papierfach. • Öffnen Sie je nach Inhalt der Meldung die obere Abdeckung oder das entsprechende Fach. • Entfernen Sie das gesamte Papier im betroffenen Bereich. Falls erforderlich, bauen Sie die Tonerpatrone, den Duplexer oder die Papierfächer aus. • Wenn die Meldung weiterhin angezeigt wird, müssen Sie alle weiteren Bereiche im Drucker auf Papier überprüfen. Vorsicht! Vergewissern Sie sich, daß das gesamte gestaute Papier vor dem Schließen der Abdeckung oder des Fachs entfernt wurde. • Öffnen und schließen Sie die obere Abdeckung, um die Meldung wieder zu löschen

Mögliche Maßnahme:

Wenn der Fehler im Einzugsbereich auftritt sind in der Regel die Einzugsrollen, Feed Roller, PickUp Roller verschmutzt oder verschlissen gegnfügig sollten diese zusammen mit dem Separation Pad erneuern werden. Bei einem Papierstau im Bereich der Fuser Unit überprüfen Sie diese auf eventuelle Beschädigungen der Heizwalzen, Film Sleeve oder auf Papierreste sowie eventuell verklemmte Papiersensoren. Im Auswurbereich kann der Fehler von verschmutzten oder verschlissenen Delivery Roller oder ebensfalls defekten oder verklemmten Sensor-Flags verursacht werden.

 
Fehler 13.x Papierstau / Error 13.x Paper jam bei HP 5Si

Fehler 13.x Papierstau / Error 13.x Paper jam bei HP 5Si

An der angegebenen Position ist ein Stau aufgetreten. • 13.1 Paper late jam at PS2.
• 13.2 Paper late jam at PS1 registration photosensor.
• 13.3 Paper late arriving late at PS1403.
• 13.4 Paper jam in fuser.
• 13.5 Paper late jam at PS1402 face-down delivery photosensor.
• 13.6 Paper jam in face-down output.

Mögliche Maßnahme:

Wenn der Fehler im Einzugsbereich auftritt sind in der Regel die Einzugsrollen, Feed Roller verschmutzt oder verschlissen gegnfügig sollten diese erneuern werden. Bei einem Papierstau im Bereich der Fuser Unit überprüfen Sie diese auf evtuelle Beschädigungen der Heizwalzen oder auf Papierreste sowie evt. verklemmte Papiersensoren. Im Auswurbereich kann der Fehler von verschmutzten oder verschlissenen Delivery Roller oder ebensfalls defekten und verklemmten Sensor-Flags verursacht werden.

 
Fehler 13.x Papierstau / Error 13.x Paper jam bei HP 4000 / 4050 / 4100 / 5000

Fehler 13.x Papierstau / Error 13.x Paper jam bei HP 4000 / 4050 / 4100 / 5000

An der angegebenen Position ist ein Stau aufgetreten. • 13.1 Paper delay jam at feed area.
• 13.2 Paper stopped jam at paper feed area. Check PS102 and PS103
• 13.5 Paper delay jam at fuser. Check tansfer roller. Check PS501 and PS106 (only on the Laserjet 4100)
• 13.6 Paper stopped jam at fuser.
• 13.10 Paper jam in Duplexer. Check PS701 and PS703
• 13.20/13.32 Paper stopped jam in paper path. Check entire paper path, check all sensors and flags.
• 13.21/13.33 Door open jam.

Mögliche Maßnahme:

Wenn der Fehler im Einzugsbereich auftritt sind in der Regel die Einzugsrollen, Feed Roller verschmutzt oder verschlissen, gegnfügig sollten diese erneuern werden. Bei einem Papierstau im Bereich der Fuser Unit überprüfen Sie diese auf evtuelle Beschädigungen der Heizwalzen, Film Sleeve oder auf Papierreste sowie evtentuell verklemmte Papiersensoren. Im Auswurbereich kann der Fehler von verschmutzten oder verschlissenen Delivery Roller oder ebensfalls defekte oder verklemmte Sensor-Flags verursacht werden. Bei der 4xx0 Serie kommt es auch vor das die Aufhängung für die Delivery Roller defekt oder gebrochen ist.

 
Fehler 13.x Papierstau / Error 13.x Paper jam bei HP 8000 / 8100

Fehler 13.x Papierstau / Error 13.x Paper jam bei HP 8000 / 8100

An der angegebenen Position ist ein Stau aufgetreten. • 13.1 Paper late jam at PS2.
• 13.2 Paper delay jam at PS1
• 13.5 Fuser output, paper late jam
• 13.6 Fuser output, paper stop jam
• 13.9 Face down delivery, paper late jam
• 13.20 Engine could not eject jam from printer
• 13.A Paper stopped at the face down bin.

Mögliche Maßnahme:

Wenn der Fehler im Einzugsbereich auftritt sind in der Regel die Einzugsrollen oder Feed Roller verschmutzt oder verschlissen, gegnfügig sollten diese erneuern werden. Bei einem Papierstau im Bereich der Fuser Unit überprüfen Sie diese auf evtuelle Beschädigungen der Heizwalzen oder auf Papierreste sowie eventuell verklemmte Papiersensoren. Im Auswurbereich kann der Fehler von verschmutzten oder verschlissenen Delivery Roller oder ebensfalls defekten oder verklemmten Sensor-Flags verursacht werden.

 
Fehler 20 zu wenig Speicher / Error 20 EM overflow / insuficcient memory

Fehler 20 zu wenig Speicher / Error 20 EM overflow / insuficcient memory

Der Drucker hat mehr Daten empfangen, als vom verfügbaren Speicher aufgenommen werden können. Evt. Haben Sie versucht, zu viele Makros, ladbare Schriftarten oder komplexe Grafiken zu übertragen.

Mögliche Maßnahme:

Drücken Sie (Taste Auswahl), um die übertragenen Daten zu drucken (dabei können einige Daten verloren gehen) oder installieren Sie zusätzlichen Speicher.

 
Fehler 21 Seite zu komplex / Error 21 / Print overrun / Page too complex

Fehler 21 Seite zu komplex / Error 21 / Print overrun / Page too complex

Die zum Drucker gesendeten Daten (viel Text, Regeln, Raster- oder Vektorgrafiken) waren zu komplex

Mögliche Maßnahme:

Drücken Sie (Taste Auswahl), um die übertragenen Daten zu drucken (dabei können einige Daten verloren gehen). Wenn diese Meldung häufiger angezeigt wird, vereinfachen Sie den Druckjob oder installieren Sie weiteren Speicher.

 
Fehler 22 EIO X Pufferüberlauf / Error I/O config

Fehler 22 EIO X Pufferüberlauf / Error I/O config

An die EIO-Karte im angegebenen Steckplatz (X) wurden zu viele Daten übertragen. Möglicherweise wird ein falsches Kommunikationsprotokoll verwendet.

Mögliche Maßnahme:

Drücken Sie (Taste Auswahl), um die Meldung zu löschen (Der Druckjob wird nicht gedruckt). Überprüfen Sie die Hostkonfiguration und ggf. das Druckerkabel.

 
Fehler 40 EIO X – Fehlerhafte Übertragung / Error 40.X Data transfer

Fehler 40 EIO X – Fehlerhafte Übertragung / Error 40.X Data transfer

Die Verbindung zwischen dem Drucker und der EIO-Karte im angegebenen Steckplatz (X) ist abgebrochen. Der Computer ist ausgeschaltet. Schlechter Kontakt zwischen Drucker und EIO/MIO Karte / Netzwerkkarte neu installieren oder zurücksetzen/reset.

Mögliche Maßnahme:

Drücken Sie (Taste Auswahl), um die Fehlermeldung zu löschen und den Druckvorgang fortzusetzen.

 
Fehler 41 / Error 41 Temporary beam detect

Fehler 41 / Error 41 Temporary beam detect

Siehe Fehler 51

 
Fehler 41.x / Error 41.x

Fehler 41.x / Error 41.x

Es ist ein vorrübergehender Druckerfehler aufgetreten. Möglicher defekt an Pasper Size Detection Board, Laser, Scanner, Engine Controller oder Formatter Board. • 41.1 Unbekannter Druckerfehler
• 41.2 Laser/Sacnner Fehlfunktion
• 41.3 Unerwartetes Papierformat
• 41.4 Kein VSYNC Signal
• 41.5 Fehler Papierzuführung (nur HP 4xx0, 5000, 8100)
• 41.5 VSREQ Fehler (nur HP 5Si)
• 41.9 VSREQ Fehler

Mögliche Maßnahme:

Überprüfen Sie sämtliche Steckerkontakte zwischen Laser, Scanner und Engine Controller Board

 
Fehler 41.3 Unerwartetes Format in Fach X / Error 41.3

Fehler 41.3 Unerwartetes Format in Fach X / Error 41.3

Dies ist in den meisten Fällen darauf zurückzuführen, dass zwei oder mehrere Bläter im Drucker aneinander haften oder dass das Papierfach nicht richtig eingestellt ist.

Mögliche Maßnahme:

Legen Sie im Fach Papier des richtigen Formats ein. Wenn Sie aus Fach 1 drucken prüfen Sie ob über das Bediehnfeld das richtige Papierformat ausgewählt wurde. Wenn Sie über Fach 2,3 oder 4 drucken überprüfen Sie ob die Einstellungen in den Papierfächern ordnungsgemäß vorgenommen wurden.

 
Fehler 49.xxxx / Error 49.xxxx

Fehler 49.xxxx / Error 49.xxxx

Es ist ein schwer wiegender Firmware-Fehler aufgetreten. Dieser kann durch fehlerhafte Druckbefehle, defekte Daten oder unerlaubte Bedienfehler hervorgerufen werden.

Mögliche Maßnahme:

Schalten Sie den Drucker aus, und schalten Sie ihn nach 20 Sekunden wieder ein. Mögliche Ursache ist ein fehlerhaftes Parallel oder Netzwerkkabel sowie eine schlechte Verbindung oder Kontakt. Eventuell tritt der Fehler nur aus bestimmten Programmen oder Softwareanwendungen auf. Überprüfen Sie den Firmware-Stand und führen Sie ggf. ein Firmware-Update durch. Schalten Sie den Drucker aus und entfernen Sie alle Optionen und Netzwerk-, Parallel-, USB- Kabel, sowie DIMMs (Außer Firmware DIMM!), Speicher, EIO-Karten aus dem Drucker. Schaltet Sie jetzt den Drucker wieder ein, wenn der Fehler jetzt NICHT mehr auftritt installieren Sie nacheinander und einzeln die ausgebauten Optionen um die fehlerhafte Baugruppe einzugrenzen. Tritt der Fehler weiterhin auf ist ggf. der Firmware DIMM oder das Formatter Board defekt.

 
Fehler 49.24.02 / Error 49.24.02

Fehler 49.24.02 / Error 49.24.02

Es ist ein schwer wiegender Fehler aufgetreten.

Mögliche Maßnahme:

Überprüfen Sie sämtliche Steckerkontakte am DC Controller. Power Supply, DC- Controller oder Formatter-Board defekt.

 
Fehler 50.x Fixiereinheit / Error 50.x Fuser

Fehler 50.x Fixiereinheit / Error 50.x Fuser

Es ist ein Fehler in der Fixiereinheit aufgetreten. • 50.1 Niedrige Fuser Temperatur
• 50.2 Fuser Aufwärmfehler
• 50.3 Fuser Temperatur zu hoch
• 50.4, 50.5, 50,6, 50.7, 50.8, 50.9 Fehler Fuser Einheit

Mögliche Maßnahme:

Vorsicht! die Fuser Unit könnte noch heiß sein! 1. Schaltet Sie den Drucker aus und überprüfen Sie ob die Fuser Unit korrekt installiert ist und die Steckkontakte in Ordnung sind.
2. Schaltet Sie den Drucker nach 20 Minuten wieder ein, tritt der Fehler weiterhin auf erneuern Sie die Fuser Unit.
Bitte beachten Sie bei ältern Druckermodelle das die Fehlermeldung nach dem ausschalten noch ca. 20 Minuten intern gespeichert wird ! Weitere Ursachen können ein defekter DC Controller und bei älteren Modellen wie HP Laserjet II und III das Netzteil sein.

 
Fehler 51.x Laser Scanner / Error 51.x

Fehler 51.x Laser Scanner / Error 51.x

Es ist ein vorrübergehender Druckerfehler aufgetreten. • 51.1 beam detect error
• 51.2 laser error

Mögliche Maßnahme:

Schaltet Sie den Drucker aus und wieder ein. Überprüfen Sie die Steckverbindungen an der Laser/Scanner Einheit. Ggf. Ist die Laser/Scanner Assy oder der DC Controller defekt.

 
Fehler 52.x Laser Scanner / Error 52.x

Fehler 52.x Laser Scanner / Error 52.x

Es ist ein vorrübergehender Druckerfehler aufgetreten. • 52.0 scanner error
• 52.1 scanner startup error
• 52.2 scanner rotatio error

Mögliche Maßnahme:

Schaltet Sie den Drucker aus und wieder ein. Überprüfen Sie die Steckverbindungen an der Laser/Scanner Einheit. Ggf. Ist die Laser/Scanner Assy oder der DC Controller defekt.

 
Fehler 51.2Y Druckerfehler

Fehler 51.2Y Druckerfehler

Entweder findet ein Laserstrahl einen Fehler oder es ist ein Laserfehler aufgetreten. Y hat folgende Werte:
• 0 – Schwarz.
• 1 – cyan
• 2 – magenta
• 3 – gelb

Mögliche Maßnahme:

Schaltet Sie den Drucker aus und wieder ein. Überprüfen Sie die Steckverbindungen an der Laser/Scanner Einheit. Ggf. Ist die Laser/Scanner Assy oder der DC Controller defekt.

 
Fehler 53.xy.zz RAM DIMM / Error 53.xy.zz

Fehler 53.xy.zz RAM DIMM / Error 53.xy.zz

Es besteht ein Problem mit dem Druckerspeicher. Das DIMM, durch das der Fehler verursacht wurde, wird nicht verwendet. X = Hardware Typ
0: ROM
1: RAM
Y = Hardware Position
0: Interner Speicher
1: Slot 1
2: Slot 2
3: Slot 3
4: Slot 4
ZZ = Fehlertyp
0: Unsupported memory
1: Unrecognized memory
2: Unsupported memory size
3: Failed ram test
4: Exceeded maximum ram size
5: Exceeded maximum rom size
6: Invalid SIMM speed
7: SIMM reporting information incorrectly
8: SIMM ram parity error
9: ROM needs to be mapped to an unsupported address
10: SIMM address conflict
11: Rom out of bounds
12: Could not make temporary mapping

Mögliche Maßnahme:

Schalten Sie den Drucker aus und installieren Sie den angegebenen Baustein erneut. Wird die Meldung weiterhin angezeigt, müssen Sie möglicherweise den angegebenen DIMM/SIMM Baustein austauschen. Schalten Sie den Drucker aus, und ersetzen Sie das DIMM/SIMM, das das Problem verursacht hat.

 
Fehler 54 Duplexer / Error 54 Duplex feed

Fehler 54 Duplexer / Error 54 Duplex feed

Fehler in der Duplex Unit

Mögliche Maßnahme:

Duplexer Unit erneuern

 
Fehler 54.xx / Error 54.x

Fehler 54.xx / Error 54.x

Diese Meldung steht in der Regel mit einem Sensorproblem in Verbindung. Das Drucken kann nicht fortgesetzt werden. Der Sensor für die Luftfeuchtigkeit der Umgebung verhält sich anormal. • 54.1 Sicherheitsstreifen an der Tonerkassette entfernen (nur HP 4100)
• 54.4 Problem mit der Stromversorgung (nur HP 4100)

Mögliche Maßnahme:

Schalten Sie den Drucker aus und dann wieder ein.

 
Fehler 55 DC Controller / Error 55 Internal communication problem

Fehler 55 DC Controller / Error 55 Internal communication problem

Es ist ein vorrübergehender Druckerfehler aufgetreten. Interner Kommunikationsfehler

Mögliche Maßnahme:

Überprüfen Sie ob das Formatter Board korrekt installiert ist und die Steckkontakte am DC Controller in Ordnung sind ggf. Fimware Update durchführen oder DC Controller und/oder Formatter Board erneuern.

 
Fehler 56.x / Error 56.x

Fehler 56.x / Error 56.x

Aufgrund einer falschen Zufuhr- oder Ausgabeanforderung ist ein vorübergehender Druckerfehler aufgetreten. • 56.1 Fehler Zufuhreinheiten
• 56.2 Fehler Ausgabeeinheiten

Mögliche Maßnahme:

Schalten Sie den Drucker aus und installieren Sie Zufuhr- und Ausgabeeinheiten wie Papierzuführung, Stacker, Stapler erneut. Eine nicht kompatibele Druckkombination wurde ausgewählt z.B. Briefumschläge im Duplexmode bedrucken ist nicht möglich.

 
Fehler 57.x Lüfter / Error 57.x Fan

Fehler 57.x Lüfter / Error 57.x Fan

Es ist ein vorübergehender Druckerfehler in einem der Lüfter des Druckers aufgetreten. X = Position Lüfter

Mögliche Maßnahme:

Schalten Sie den Drucker aus und dann wieder ein. Erneuern Sie den defekten Lüfter.

 
Fehler 57.x Lüfter / Error 57.x Fan bei HP 4000 / 4050 / 4100 / 5000

Fehler 57.x Lüfter / Error 57.x Fan bei HP 4000 / 4050 / 4100 / 5000

Es ist ein vorübergehender Druckerfehler in einem der Lüfter des Druckers aufgetreten. • 57.4 Druckerlüfter
• 57.7 Duplexlüfter

Mögliche Maßnahme:

Schalten Sie den Drucker aus und dann wieder ein. Erneuern Sie den defekten Lüfter.

 
Fehler 57.x Lüfter / Error 57.x Fan bei HP 8000 / 8100

Fehler 57.x Lüfter / Error 57.x Fan bei HP 8000 / 8100

57.2 Fan 3 location: formatter • 57.3 Fan 2 location: Low-voltage powersupply • 57.5 Fan 1 location: Laser/Scanner • 57.6 Fan 4 location: Face down delivery

Mögliche Maßnahme:

Schalten Sie den Drucker aus und dann wieder ein. Erneuern Sie den defekten Lüfter.

 
Fehler 58.x / Error 58.x

Fehler 58.x / Error 58.x

Es ist ein Druckerfehler aufgrund eines Speicher-Tag-CPU-Fehlers aufgetreten, oder es besteht ein Problem mit dem Umluftsensor oder der Stromversorgung. • 58.2 Air Temp Sensor
• 58.3 DC Controller oder CPU
• 58.4 Power Supply

Mögliche Maßnahme:

Überprüfen Sie die Stromversorgung.

 
Fehler 58.x / Error 58.x bei HP Laserjet 8000 / 8100 !

Fehler 58.x / Error 58.x bei HP Laserjet 8000 / 8100 !

58.1 Tray 1 lifter malfunction • 58.2 Tray 2 lifter malfunction • 58.3 Tray 3 lifter malfunction • 58.4 Tray 4 lifter malfunction

Mögliche Maßnahme:

Überprüfen Sie den Lift-Motor und erneuern ihn ggf.

 
Fehler 59.x / Error 59.x bei HP Laserjet 4xx0 / 5000 / 8000 / 8100

Fehler 59.x / Error 59.x bei HP Laserjet 4xx0 / 5000 / 8000 / 8100

59.0 Main motor error • 59.1 Main motor startup error • 59.2 main motor rotation error

Mögliche Maßnahme:

Überprüfen Sie das Druckwerk auf Fremdgegenstände die evt. den Antrieb blockieren. Ein defekte/schwergängige Toner-Kassette oder Fuser Unit können diesen Fehler auch verursachen.Ggf. Main Motor oder/und DC Controller erneuern.

 
Fehler 60.x / Error 60.x bei HP Laserjet 4200 / 4300 Serie

Fehler 60.x / Error 60.x bei HP Laserjet 4200 / 4300 Serie

60.2 Tray 2 Lift Error • 60.3 Tray 3 Lift Error • 60.4 Tray 4 Lift Error

Mögliche Maßnahme:

Überprüfen Sie die Papierzuführungen auf Fremdgegenstände die evt. den Antrieb blockieren. Evt. Lift Driver Assy oder DC Controller erneuern.

 
Fehler 62 / Error 62 bei HP Laserjet 2300 / 4200 / 4300 Serie

Fehler 62 / Error 62 bei HP Laserjet 2300 / 4200 / 4300 Serie

Diese Meldung weisst darauf hin, dass kein System gefunden werden konnte. Das Softwaresystem des Druckers ist beschädigt.

Mögliche Maßnahme:

Installieren Sie den Firmware DIMM Slot 1 erneut, ggf. Firmware Dimm und/oder Formatter Board erneuern.

 
Fehler 62.x / Error 62.x bei HP Laserjet 4000 / 4050 / 4100 / 5000 / 8000 / 810

Fehler 62.x / Error 62.x bei HP Laserjet 4000 / 4050 / 4100 / 5000 / 8000 / 810

Es ist ein vorübergehender Druckerfehler in einem der Druckerspeicher aufgetreten. • 62.0 = interner Speicher
• 62.1 = DIMM Slot 1
• 62.2 = DIMM Slot 2
• 62.3 = DIMM Slot 3
• 62.4 = DIMM Slot 4

Mögliche Maßnahme:

Installieren Sie den Speicher / DIMM erneut oder tauschen Sie diesen ggf. gegen einen neuen aus.

 
Fehler 64 / Error 64

Fehler 64 / Error 64

Im Scan-Puffer ist ein vorübergehender Druckerfehler aufgetreten.

Mögliche Maßnahme:

Schalten Sie den Drucker aus und dann wieder ein, ggf. Formatter Board erneuern.

 
Fehler 66.xx.yy / Error 66.xx.yy

Fehler 66.xx.yy / Error 66.xx.yy

In einem externen Zubehör ist ein Fehler aufgetreten.

Mögliche Maßnahme:

Schalten Sie den Drucker aus und überprüfen Sie ob das Zubehörgerät ordnungsgemäß installiert und angeschlossen ist, schalten Sie dann den Drucker wieder ein.

 
Fehler 68.x / Error 68.x

Fehler 68.x / Error 68.x

Im permanenten Speicher des Druckers ist ein Fehler aufgetreten oder der Speicher ist voll. Einige Einstellungen wurden vermutlich auf die Werkseinstellungen zurückgesetzt.

Mögliche Maßnahme:

Schalten Sie den Drucker aus und dann wieder ein, führen Sie ggf. Einen Cold Reset durch der den Drucker auf die Werkseinstellungen zurücksetzt und konfigurieren dann Ihre Benutzer definierten Einstellungen erneut. Falls der Fehler erneut auftritt muß ggf. die Festplatte neu initialisieren oder das Formatter Board erneuern.

 
Fehler 69.x / Error 69.x

Fehler 69.x / Error 69.x

Ein Fehler in der Duplexeinheit ist aufgetreten.

Mögliche Maßnahme:

Schalten Sie den Drucker aus und installieren Sie Duplexeinheit erneut, schalten Sie dann den Drucker wieder ein.

 
Fehler 79.x / Error 79.x

Fehler 79.x / Error 79.x

Es wurde ein schwer wiegender Hardwarefehler erkannt.

Mögliche Maßnahme:

Schalten Sie den Drucker aus, und schalten Sie ihn nach 20 Sekunden wieder ein. Eventuell tritt der Fehler nur aus bestimmten Programmen oder Softwareanwendungen auf. Überprüfen Sie den Firmware-Stand und führen Sie ggf. ein Firmware-Update durch. Schalten Sie den Drucker aus und entfernen Sie alle Optionen und Netzwerk-, Parallel-, USB- Kabel, sowie DIMMs (Außer Firmware DIMM!), Speicher, EIO-Karten aus dem Drucker. Schaltet Sie jetzt den Drucker wieder ein, wenn der Fehler jetzt NICHT mehr auftritt installieren Sie nacheinander und einzeln die ausgebauten Optionen um die fehlerhafte Baugruppe einzugrenzen. Tritt der Fehler weiterhin auf ist ggf. der Firmware DIMM oder das Formatter Board defekt.

 
Fehler 80.x / Error 80.x

Fehler 80.x / Error 80.x

Am EIO / MIO-Zubehör in Steckplatz (X) ist ein schwer wiegender Fehler augetreten.

Mögliche Maßnahme:

Vorsicht! Installieren Sie die MIO / EIO Karte erneut ggf. auf einem anderen Steckplatz. Reseten Sie die MIO / EIO Karte. Ggf. iie Karte oder das Formatter Board erneuern.

 
01:10 error

01:10 error

Electronics module failure

 
01:11 error

01:11 error

Electronics module fan failure

 
01:12 error

01:12 error

EEROM not configured correctly

 
01:13 error

01:13 error

Electronics module failure

 
02:10 error

02:10 error

Carriage failure

 
02:13 error

02:13 error

Carriage failure

 
03:10 error

03:10 error

Power supply failure

 
04:11 error

04:11 error

LAN card not detected

 
05:09 error

05:09 error

Formatter or HP GL/2 card not detected

 
05:10 error

05:10 error

Formatter not detected

 
05:11 error

05:11 error

Formatter not detected

 
06:03 error

06:03 error

Formatter hard drive not functioning

 
08:11 error

08:11 error

Front panel not detected

 
11:11 error

11:11 error

Trailing cable defective

 
11:13 error

11:13 error

Printhead voltage: Possible trailing cable or carriage defective

 
12:11 error

12:11 error

Attempt to resolve by cleaning printheads or possible defective carriage

 
21:10 error

21:10 error

Service station failure

 
21:11 error

21:11 error

Attempt to resolve by firmware upgrade or possible defective s/stn

 
22:10 error

22:10 error

Ensure all inks are genuine HP or possible Ink supply station failure

 
41:10 error

41:10 error

Paper axis (X-Axis) motor failure

 
41:13 error

41:13 error

Paper axis motor encoder failure

 
42:10 error

42:10 error

Scan axis (Y-Axis) motor failure

 
43:10 error

43:10 error

Vacuum fan failure

 
43:11 error

43:11 error

Vacuum fan not detected

 
56:10 error

56:10 error

Drive roller encoder sensor failure

 
56:13 error

56:13 error

Drive roller encoder sensor failure

 
61:04 error

61:04 error

Firmware error, attempt to resolve by firmware upgrade

 
61:05 error

61:05 error

Communication problem, try new driver & different connection method

 
62:03 error

62:03 error

Parallel port communication error, call us to discuss

 
63:03 error

63:03 error

LAN card communication error, attempt firmware upgrade

 
64:03 error

64:03 error

USB port communication error, attempt firmware upgrade

 
64:04 error

64:04 error

USB port communication error, attempt firmware upgrade

 
65:03 error

65:03 error

Communication error, attempt firmware upgrade / driver upgrade

 
71:04 error

71:04 error

Formatter issue, attempt firmware upgrade

 
71:06 error

71:06 error

Out of memory, request quote for memory upgrade

 
72:04 error

72:04 error

Scan axis firmware error, attempt firmware upgrade

 
73:04 error

73:04 error

Servo error, Possible new electronics module

 
79:04 error

79:04 error

Firmware error, attempt firmware upgrade

 
81:01 error

81:01 error

Paper axis shutdown, possible defective encoder disk

 
81:11 error

81:11 error

Paper axis shutdown, possible defective encoder disk

 
85:10 error

85:10 error

Paper axis encoder error, possible defective encoder/sensor

 
86:01 error

86:01 error

Carriage axis shutdown

 
86:11 error

86:11 error

Carriage axis shutdown

 
86:13 error

86:13 error

Carriage axis shutdown, attempt firmware upgrade

 
87:13 error

87:13 error

Possible defective carriage assembly

 
93:10 error

93:10 error

Ink system failure, check inks are ok & genuine HP, possible tubes assy

 
01:10 error

01:10 error

Electronics module failure

 
01:11 error

01:11 error

Electronics module fan failure

 
01:12 error

01:12 error

EEROM not configured correctly

 
01:13 error

01:13 error

Electronics module failure

 
02:10 error

02:10 error

Carriage failure

 
02:13 error

02:13 error

Carriage failure

 
03:10 error

03:10 error

Power supply failure

 
04:11 error

04:11 error

LAN card not detected

 
05:09 error

05:09 error

Formatter or HP GL/2 card not detected

 
05:10 error

05:10 error

Formatter not detected

 
05:11 error

05:11 error

Formatter not detected

 
06:03 error

06:03 error

Formatter hard drive not functioning

 
08:11 error

08:11 error

Front panel not detected

 
11:11 error

11:11 error

Trailing cable defective

 
11:13 error

11:13 error

Printhead voltage: Possible trailing cable or carriage defective

 
12:11 error

12:11 error

Attempt to resolve by cleaning printheads or possible defective carriage

 
21:10 error

21:10 error

Service station failure

 
21:11 error

21:11 error

Attempt to resolve by firmware upgrade or possible defective s/stn

 
22:10 error

22:10 error

Ensure all inks are genuine HP or possible Ink supply station failure

 
41:10 error

41:10 error

Paper axis (X-Axis) motor failure

 
41:13 error

41:13 error

Paper axis motor encoder failure

 
42:10 error

42:10 error

Scan axis (Y-Axis) motor failure

 
43:10 error

43:10 error

Vacuum fan failure

 
43:11 error

43:11 error

Vacuum fan not detected

 
56:10 error

56:10 error

Drive roller encoder sensor failure

 
56:13 error

56:13 error

Drive roller encoder sensor failure

 
61:04 error

61:04 error

Firmware error, attempt to resolve by firmware upgrade

 
61:05 error

61:05 error

Communication problem, try new driver & different connection method

 
62:03 error

62:03 error

Parallel port communication error, call us to discuss

 
63:03 error

63:03 error

LAN card communication error, attempt firmware upgrade

 
64:03 error

64:03 error

USB port communication error, attempt firmware upgrade

 
64:04 error

64:04 error

USB port communication error, attempt firmware upgrade

 
65:03 error

65:03 error

Communication error, attempt firmware upgrade / driver upgrade

 
71:04 error

71:04 error

Formatter issue, attempt firmware upgrade

 
71:06 error

71:06 error

Out of memory, request quote for memory upgrade

 
72:04 error

72:04 error

Scan axis firmware error, attempt firmware upgrade

 
73:04 error

73:04 error

Servo error, Possible new electronics module

 
79:04 error

79:04 error

Firmware error, attempt firmware upgrade

 
81:01 error

81:01 error

Paper axis shutdown, possible defective encoder disk

 
81:11 error

81:11 error

Paper axis shutdown, possible defective encoder disk

 
85:10 error

85:10 error

Paper axis encoder error, possible defective encoder/sensor

 
86:01 error

86:01 error

Carriage axis shutdown

 
86:11 error

86:11 error

Carriage axis shutdown

 
86:13 error

86:13 error

Carriage axis shutdown, attempt firmware upgrade

 
87:13 error

87:13 error

Possible defective carriage assembly

 
93:10 error

93:10 error

Ink system failure, check inks are ok & genuine HP, possible tubes assy

 
010001 error

010001 error

Window sensor defective, front panel required

 
010020 error

010020 error

ROM test failure, possible main PCA

 
010021 error

010021 error

DRAM failure replace main PCA

 
010022 error

010022 error

Swath RAM failure, replace main PCA

 
010023 error

010023 error

EEROM failure, clear EEROM / Replace main PCA

 
010024 error

010024 error

Pen interface failure, replace main PCA

 
010030 error

010030 error

Internal communication error

 
010032 error

010032 error

Internal communication error

 
010033 error

010033 error

Internal communication error

 
010034 error

010034 error

Internal communication error

 
010040 error

010040 error

X-Axis servo error

 
010041 error

010041 error

Y-Axis servo error

 
010050 error

010050 error

Defective Postscript SIMM

 
010060 error

010060 error

Primer motor failure

 
010080 error

010080 error

RS-232 data overflow

 
020001 error

020001 error

Memory error, try turning off queuing & adding more RAM

 
020002 error

020002 error

Memory error, try turning off queuing & adding more RAM

 
02002x error

02002x error

Firmware error, replace Postscript SIMM

 
030010 error

030010 error

Service station error

 
04xxxx error

04xxxx error

MIO error, check MIO setup

 
040601 error

040601 error

Incorrect MIO card

 
05xxxx error

05xxxx error

MIO system error

 
06030A error

06030A error

Mark Position not found, possible carriage assy

 
06030B error

06030B error

Bad ambient temperature

 
060308 error

060308 error

Problem with pen voltage

 
060309 error

060309 error

Problem with pen voltage

 
070000 error

070000 error

Unable to calibrate drop detect

 
070005 error

070005 error

Calibration problem

 
070006 error

070006 error

Calibration problem

 
070007 error

070007 error

Calibration problem

 
070008 error

070008 error

Calibration problem

 
070010 error

070010 error

False drops detected, check your power supply is not noisy

 
070020 error

070020 error

Drop detect error

 
070030 error

070030 error

Drop detect error

 
070100 error

070100 error

Firmware error

 
0000D8 error

0000D8 error

Firmware error

 
080001 error

080001 error

Postscript error

 
010001 error

010001 error

Window sensor defective, front panel required

 
010020 error

010020 error

ROM test failure, possible main PCA

 
010021 error

010021 error

DRAM failure replace main PCA

 
010022 error

010022 error

Swath RAM failure, replace main PCA

 
010023 error

010023 error

EEROM failure, clear EEROM / Replace main PCA

 
010024 error

010024 error

Pen interface failure, replace main PCA

 
010030 error

010030 error

Internal communication error

 
010032 error

010032 error

Internal communication error

 
010033 error

010033 error

Internal communication error

 
010034 error

010034 error

Internal communication error

 
010040 error

010040 error

X-Axis servo error

 
010041 error

010041 error

Y-Axis servo error

 
010050 error

010050 error

Defective Postscript SIMM

 
010060 error

010060 error

Primer motor failure

 
010080 error

010080 error

RS-232 data overflow

 
020001 error

020001 error

Memory error, try turning off queuing & adding more RAM

 
020002 error

020002 error

Memory error, try turning off queuing & adding more RAM

 
02002x error

02002x error

Firmware error, replace Postscript SIMM

 
030010 error

030010 error

Service station error

 
04xxxx error

04xxxx error

MIO error, check MIO setup

 
040601 error

040601 error

Incorrect MIO card

 
05xxxx error

05xxxx error

MIO system error

 
06030A error

06030A error

Mark Position not found, possible carriage assy

 
06030B error

06030B error

Bad ambient temperature

 
060308 error

060308 error

Problem with pen voltage

 
060309 error

060309 error

Problem with pen voltage

 
070000 error

070000 error

Unable to calibrate drop detect

 
070005 error

070005 error

Calibration problem

 
070006 error

070006 error

Calibration problem

 
070007 error

070007 error

Calibration problem

 
070008 error

070008 error

Calibration problem

 
070010 error

070010 error

False drops detected, check your power supply is not noisy

 
070020 error

070020 error

Drop detect error

 
070030 error

070030 error

Drop detect error

 
070100 error

070100 error

Firmware error

 
0000D8 error

0000D8 error

Firmware error

 
080001 error

080001 error

Postscript error

 
01:10 error

01:10 error

Electronics module failure

 
01:11 error

01:11 error

Electronics module fan failure

 
01:12 error

01:12 error

EEROM not configured correctly

 
01:13 error

01:13 error

Electronics module failure

 
02:10 error

02:10 error

Carriage failure

 
02:13 error

02:13 error

Carriage failure

 
03:10 error

03:10 error

Power supply failure

 
04:11 error

04:11 error

LAN card not detected

 
05:09 error

05:09 error

Formatter or HP GL/2 card not detected

 
05:10 error

05:10 error

Formatter not detected

 
05:11 error

05:11 error

Formatter not detected

 
06:03 error

06:03 error

Formatter hard drive not functioning

 
08:11 error

08:11 error

Front panel not detected

 
11:11 error

11:11 error

Trailing cable defective

 
11:13 error

11:13 error

Printhead voltage: Possible trailing cable or carriage defective

 
12:11 error

12:11 error

Attempt to resolve by cleaning printheads or possible defective carriage

 
21:10 error

21:10 error

Service station failure

 
21:11 error

21:11 error

Attempt to resolve by firmware upgrade or possible defective s/stn

 
22:10 error

22:10 error

Ensure all inks are genuine HP or possible Ink supply station failure

 
41:10 error

41:10 error

Paper axis (X-Axis) motor failure

 
41:13 error

41:13 error

Paper axis motor encoder failure

 
42:10 error

42:10 error

Scan axis (Y-Axis) motor failure

 
43:10 error

43:10 error

Vacuum fan failure

 
43:11 error

43:11 error

Vacuum fan not detected

 
56:10 error

56:10 error

Drive roller encoder sensor failure

 
56:13 error

56:13 error

Drive roller encoder sensor failure

 
61:04 error

61:04 error

Firmware error, attempt to resolve by firmware upgrade

 
61:05 error

61:05 error

Communication problem, try new driver & different connection method

 
62:03 error

62:03 error

Parallel port communication error, call us to discuss

 
63:03 error

63:03 error

LAN card communication error, attempt firmware upgrade

 
64:03 error

64:03 error

USB port communication error, attempt firmware upgrade

 
64:04 error

64:04 error

USB port communication error, attempt firmware upgrade

 
65:03 error

65:03 error

Communication error, attempt firmware upgrade / driver upgrade

 
71:04 error

71:04 error

Formatter issue, attempt firmware upgrade

 
71:06 error

71:06 error

Out of memory, request quote for memory upgrade

 
72:04 error

72:04 error

Scan axis firmware error, attempt firmware upgrade

 
73:04 error

73:04 error

Servo error, Possible new electronics module

 
79:04 error

79:04 error

Firmware error, attempt firmware upgrade

 
81:01 error

81:01 error

Paper axis shutdown, possible defective encoder disk

 
81:11 error

81:11 error

Paper axis shutdown, possible defective encoder disk

 
85:10 error

85:10 error

Paper axis encoder error, possible defectice encoder/sensor

 
86:01 error

86:01 error

Carriage axis shutdown

 
86:11 error

86:11 error

Carriage axis shutdown

 
86:13 error

86:13 error

Carriage axis shutdown, attempt firmware upgrade

 
87:13 error

87:13 error

Possible defective carriage assembly

 
93:10 error

93:10 error

Ink system failure, check inks are ok & genuine HP, possible tubes assy

 
0B0000 error

0B0000 error

Bad Ambient Temperture Measured

 
0B0001 error

0B0001 error

Bad Humidity Read

 
0B0002 error

0B0002 error

Bad IDS Pressure Read

 
0B0003 error

0B0003 error

ACDO Intrenal Channles Check Failure

 
0B0004 error

0B0004 error

Unable To Detect Pump

 
0B0005 error

0B0005 error

Unable To Detect Valve

 
0B0006 error

0B0006 error

Trailing Cable Incorrectly Connected OR Fuse In Electronics Module Has Burned

 
0B0007 error

0B0007 error

Unable To Detect Vacuum Fan

 
0B0008 error

0B0008 error

Unable To Detect Cooling Fan

 
0B0009 error

0B0009 error

Unable To Detect Aerosol Fan (Including On Right Cover)

 
0B000A error

0B000A error

Primer Shut Down Error

 
0B000B error

0B000B error

Pump Or Pressure Sensor Not Working

 
0B000C error

0B000C error

Serial Device ADC Test Failure

 
0B000D error

0B000D error

24 V Source Test Failure

 
0B000E error

0B000E error

Short Circuit In Scan-Axis Motor

 
0000D8 error

0000D8 error

External Library Error

 
01002D error

01002D error

The Main PCA Cannot Communicate With The Carriage

 
010020 error

010020 error

FirmWare DIMM Test Failure

 
010021 error

010021 error

Memory Module Test Failure

 
010023 error

010023 error

EEROM Test Failure

 
010028 error

010028 error

EEROM Checksum Failure

 
010029 error

010029 error

EEROM Write Failure

 
010040 error

010040 error

Error In Paper-Axis Encoder Quadrature

 
010041 error

010041 error

Error In Scan-Axis Encoder Quadrature

 
010042 error

010042 error

Error In Service Station-Axis Encoder Quadrature

 
010050 error

010050 error

PostScript Processing Error

 
01009X error

01009X error

Error In Paper-Axis Motor Encoder

 
02xxxx error

02xxxx error

PostScript/Firmware Error

 
04Cxxx error

04Cxxx error

EIO Accessories (EIO Card/Hard Disk Drive) Error

 
048xxx error

048xxx error

EIO Card Is From A Third Party Vendor May Not Be Fully Compliant With IIO Protocol Specification2.0 OR EIO Card Firmware Is Not Updated

 
048500 error

048500 error

There Are Too Many EIO Cards Connected To Printer

 
060300 error

060300 error

One Of The Printheads Has Internal Electrical Problem

 
060301 error

060301 error

One Of The Printheads Has Internal Electrical Problem

 
060305 error

060305 error

Thermal Shutdown Error(One Of The Printheads Has Gone Above Maximum Temperature)

 
060306 error

060306 error

Problem With Printhead Selection

 
060307 error

060307 error

APA Regulation Failure

 
060308 error

060308 error

APA Regulation Failure

 
060309 error

060309 error

Problem With Setting The Voltage Of Printheads

 
06030A error

06030A error

Error In Finding The Mark Encoder

 
06030B error

06030B error

The Ambient Temperature Measured Is Out Of The Normal Range

 
070100 error

070100 error

Firmware Error

 
080001 error

080001 error

PostScript Error

 
09xxxx error

09xxxx error

EIO Accessories (EIO Card/Hard Disk Drive) Error

 
09Axxx error

09Axxx error

Internal Error

 
09A001 error

09A001 error

There Are Too Many Hard Disk Drives Connected To The Printer

 
09Bxxx error

09Bxxx error

Internal Error

 
09Cxxx error

09Cxxx error

Internal Error

 
0A0000 error

0A0000 error

The Air Pressure Is Below The Minimum Requirement

 
0A0010 error

0A0010 error

Problem In Pressurizing The Air System

 
0A0020 error

0A0020 error

Error In Calibrating The APS Sensor

 
0A0030 error

0A0030 error

Problem In Depressurizing Air System

 
0A0040 error

0A0040 error

Ink Tubes Initialization Failure Due To Low Air Pressure

 
0A0050 error

0A0050 error

The Printer Has Detected A Leak In The Tubes System Before The Life Of The System

 
0A0060 error

0A0060 error

The Printer Has Detected A Leak In The Tubes System After The Life Of The System

 
0A0070 error

0A0070 error

The Backup EEROM Contents Stored In The Tubes Systems Are Not Consistent With The Ones Required By The Firmware

 
0C0030 error

0C0030 error

Bad Drop Detector

 
0C0032 error

0C0032 error

Drop Detector Not Calibrated For All Printheads

 
0C1000 error

0C1000 error

Primer Not Calibrated

 
0C1001 error

0C1001 error

Primer Shutdown Error

 
0D00 error

0D00 error

System Error Code Related To The Multi-roll Feeder

 
0B0000 error

0B0000 error

Bad Ambient Temperture Measured

 
0B0001 error

0B0001 error

Bad Humidity Read

 
0B0002 error

0B0002 error

Bad IDS Pressure Read

 
0B0003 error

0B0003 error

ACDO Intrenal Channles Check Failure

 
0B0004 error

0B0004 error

Unable To Detect Pump

 
0B0005 error

0B0005 error

Unable To Detect Valve

 
0B0006 error

0B0006 error

Trailing Cable Incorrectly Connected OR Fuse In Electronics Module Has Burned

 
0B0007 error

0B0007 error

Unable To Detect Vacuum Fan

 
0B0008 error

0B0008 error

Unable To Detect Cooling Fan

 
0B0009 error

0B0009 error

Unable To Detect Aerosol Fan (Including On Right Cover)

 
0B000A error

0B000A error

Primer Shut Down Error

 
0B000B error

0B000B error

Pump Or Pressure Sensor Not Working

 
0B000C error

0B000C error

Serial Device ADC Test Failure

 
0B000D error

0B000D error

24 V Source Test Failure

 
0B000E error

0B000E error

Short Circuit In Scan-Axis Motor

 
0000D8 error

0000D8 error

External Library Error

 
01002D error

01002D error

The Main PCA Cannot Communicate With The Carriage

 
010020 error

010020 error

FirmWare DIMM Test Failure

 
010021 error

010021 error

Memory Module Test Failure

 
010023 error

010023 error

EEROM Test Failure

 
010028 error

010028 error

EEROM Checksum Failure

 
010029 error

010029 error

EEROM Write Failure

 
010040 error

010040 error

Error In Paper-Axis Encoder Quadrature

 
010041 error

010041 error

Error In Scan-Axis Encoder Quadrature

 
010042 error

010042 error

Error In Service Station-Axis Encoder Quadrature

 
010050 error

010050 error

PostScript Processing Error

 
01009X error

01009X error

Error In Paper-Axis Motor Encoder

 
02xxxx error

02xxxx error

PostScript/Firmware Error

 
04Cxxx error

04Cxxx error

EIO Accessories (EIO Card/Hard Disk Drive) Error

 
048xxx error

048xxx error

EIO Card Is From A Third Party Vendor May Not Be Fully Compliant With IIO Protocol Specification2.0 OR EIO Card Firmware Is Not Updated

 
048500 error

048500 error

There Are Too Many EIO Cards Connected To Printer

 
060300 error

060300 error

One Of The Printheads Has Internal Electrical Problem

 
060301 error

060301 error

One Of The Printheads Has Internal Electrical Problem

 
060305 error

060305 error

Thermal Shutdown Error (One Of The Printheads Has Gone Above Maximum Temperature)

 
060306 error

060306 error

Problem With Printhead Selection

 
060307 error

060307 error

APA Regulation Failure

 
060308 error

060308 error

APA Regulation Failure

 
060309 error

060309 error

Problem With Setting The Voltage Of Printheads

 
06030A error

06030A error

Error In Finding The Mark Encoder

 
06030B error

06030B error

The Ambient Temperature Measured Is Out Of The Normal Range

 
070100 error

070100 error

Firmware Error

 
080001 error

080001 error

PostScript Error

 
09xxxx error

09xxxx error

EIO Accessories (EIO Card/Hard Disk Drive) Error

 
09Axxx error

09Axxx error

Internal Error

 
09A001 error

09A001 error

There Are Too Many Hard Disk Drives Connected To The Printer

 
09Bxxx error

09Bxxx error

Internal Error

 
09Cxxx error

09Cxxx error

Internal Error

 
0A0000 error

0A0000 error

The Air Pressure Is Below The Minimum Requirement

 
0A0010 error

0A0010 error

Problem In Pressurizing The Air System

 
0A0020 error

0A0020 error

Error In Calibrating The APS Sensor

 
0A0030 error

0A0030 error

Problem In Depressurizing Air System

 
0A0040 error

0A0040 error

Ink Tubes Initialization Failure Due To Low Air Pressure

 
0A0050 error

0A0050 error

The Printer Has Detected A Leak In The Tubes System Before The Life Of The System

 
0A0060 error

0A0060 error

The Printer Has Detected A Leak In The Tubes System After The Life Of The System

 
0A0070 error

0A0070 error

The Backup EEROM Contents Stored In The Tubes Systems Are Not Consistent With The Ones Required By The Firmware

 
0C0030 error

0C0030 error

Bad Drop Detector

 
0C0032 error

0C0032 error

Drop Detector Not Calibrated For All Printheads

 
0C1000 error

0C1000 error

Primer Not Calibrated

 
0C1001 error

0C1001 error

Primer Shutdown Error

 
0D00 error

0D00 error

System Error Code Related To The Multi-roll Feeder

 
010020 error

010020 error

The CheckSum Read On The Flash SIMM Is Incorrect

 
010021 error

010021 error

The Base DRAM Or The RAM SIMM Tests Failed

 
010022 error

010022 error

The SWATH RAM Test Failed

 
010023 error

010023 error

A Fuse On The Main PCA Has Blown

 
010025 error

010025 error

Problem Initializing The Encoder Pulse Generator

 
010030 error

010030 error

One Of The Two Interconnect Boards Not Detected

 
010031 error

010031 error

The Printhead Primitive Driver ASIC Test Failed

 
010032 error

010032 error

Fan Test Failed – Current Not Detected In One Or Both Fans

 
010033 error

010033 error

The DC Motor ASIC Test Failed

 
010034 error

010034 error

One Of The DC Motor Has Failed

 
010035 error

010035 error

One Of The Stepper Motors Has Failed

 
010036 error

010036 error

ADC Test Failure In The Main PCA

 
010037 error

010037 error

ADC Test Failure In The Carriage PCA

 
010038 error

010038 error

A Printhead Voltage Could Not Be Set – Main PCA Failure

 
010039 error

010039 error

A Printhead Voltage Could Not Be Set – Carriage PCA Failure

 
010040 error

010040 error

The Ambient Temperature Measured Is Out Of The Normal Range

 
010041 error

010041 error

Problem In Setting The Printhead Voltage

 
010042 error

010042 error

The Status Of One Of The Optical Sensors Is Not Stable When It Should Be

 
010100 error

010100 error

Error Reading In The EEROM

 
010101 error

010101 error

An Action Outside The EEROM Limits Has Been Performed

 
010102 error

010102 error

Physical EEROM Write And/Or Write Operations Failed. The EEROM Data That Is Written Does Not Match The Data That Is Read

 
010110 error

010110 error

The Content Of The Permanent Configuration Area Of The EEROM Is Not Valid When The Printer Is initialised In Service Mode

 
010111 error

010111 error

The Content Of The User Configuration Area EEROM Is Not Valid When The Printer Is initialised

 
010120 error

010120 error

The Content Of The Permanent Configuration Area Of The EERom Is Not Valid When Printer Is initialised In Normal Mode

 
010121 error

010121 error

One Of The Banks Of The User Area Was Corrupted While Writing Or Reading In That Area

 
020000 error

020000 error

Error In Finding The Primer Home Position

 
020001 error

020001 error

Error In Finding The Elevator Home Position

 
020002 error

020002 error

Error In Finding The Refill Arm Home Position

 
020003 error

020003 error

Error In Finding The refill Stepper Motor Home Position

 
020004 error

020004 error

Error In Finding The Service Station Home Position

 
020005 error

020005 error

Elevator Has A Problem Reaching A Desired Position

 
020006 error

020006 error

The Refill Position In The Y-axis In Not Calibrated

 
020010 error

020010 error

Problem With Fine Movement of The Y-Axis Motor

 
020011 error

020011 error

Error During Initialization Of The Y-Axis

 
040xxx error

040xxx error

MIO Card Error

 
040601 error

040601 error

The MIO Card Does Not Support The MIO 6 Protocol Cards With Vision 5 Or Below Can Not Be Used With The Plotter. Version 5.1 Cards Behave As Expected But Does Not Support PML Intructions

 
050000 error

050000 error

The Line Sensor Has Problems Finding The Mark Encoder

 
060000 error

060000 error

The Line Sensor Is Not Functioning Properly Because There Is To Much Ambient Light

 
060200 error

060200 error

Incompatible Firmware And Carriage PCA

 
060399 error

060399 error

Incompatible Firmware And Line Sensor

 
07xxxx error

07xxxx error

Firmware Error

 
08xxxx error

08xxxx error

PostScript Error

 
080001 error

080001 error

Hard Disk Drive Installed Without PostScript

 
09xxxx error

09xxxx error

Problem With The Hard Disk

 
09004 error

09004 error

PostScript Installed Without The Hard Disk Drive

 
010020 error

010020 error

The CheckSum Read On The Flash SIMM Is Incorrect

 
010021 error

010021 error

The Base DRAM Or The RAM SIMM Tests Failed

 
010022 error

010022 error

The SWATH RAM Test Failed

 
010023 error

010023 error

A Fuse On The Main PCA Has Blown

 
010025 error

010025 error

Problem Initializing The Encoder Pulse Generator

 
010030 error

010030 error

One Of The Two Interconnect Boards Not Detected

 
010031 error

010031 error

The Printhead Primitive Driver ASIC Test Failed

 
010032 error

010032 error

Fan Test Failed – Current Not Detected In One Or Both Fans

 
010033 error

010033 error

The DC Motor ASIC Test Failed

 
010034 error

010034 error

One Of The DC Motor Has Failed

 
010035 error

010035 error

One Of The Stepper Motors Has Failed

 
010036 error

010036 error

ADC Test Failure In The Main PCA

 
010037 error

010037 error

ADC Test Failure In The Carriage PCA

 
010038 error

010038 error

A Printhead Voltage Could Not Be Set – Main PCA Failure

 
010039 error

010039 error

A Printhead Voltage Could Not Be Set – Carriage PCA Failure

 
010040 error

010040 error

The Ambient Temperature Measured Is Out Of The Normal Range

 
010041 error

010041 error

Problem In Setting The Printhead Voltage

 
010042 error

010042 error

The Status Of One Of The Optical Sensors Is Not Stable When It Should Be

 
010100 error

010100 error

Error Reading In The EEROM

 
010101 error

010101 error

An Action Outside The EEROM Limits Has Been Performed

 
010102 error

010102 error

Physical EEROM Write And/Or Write Operations Failed. The EEROM Data That Is Written Does Not Match The Data That Is Read

 
010110 error

010110 error

The Content Of The Permanent Configuration Area Of The EEROM Is Not Valid When The Printer Is Initialised In Service Mode

 
010111 error

010111 error

The Content Of The User Configuration Area EEROM Is Not Valid When The Printer Is initialised

 
010120 error

010120 error

The Content Of The Permanent Configuration Area Of The EERom Is Not Valid When Printer Is initialised In Normal Mode

 
010121 error

010121 error

One Of The Banks Of The User Area Was Corrupted While Writing Or Reading In That Area

 
025000 error

025000 error

Error In Finding The Primer Home Position

 
025001 error

025001 error

Error In Finding The Elevator Home Position

 
025002 error

025002 error

Error In Finding The Refill Arm Home Position

 
025003 error

025003 error

Error In Finding The refill Stepper Motor Home Position

 
025004 error

025004 error

Error In Finding The Service Station Home Position

 
025005 error

025005 error

Elevator Has A Problem Reaching A Desired Position

 
025006 error

025006 error

The Refill Position In The Y-axis In Not Calibrated

 
020010 error

020010 error

Problem With Fine Movement of The Y-Axis Motor

 
020011 error

020011 error

Error During Initialization Of The Y-Axis

 
040xxx error

040xxx error

MIO Card Error

 
040601 error

040601 error

The MIO Card Does Not Support The MIO 6 Protocol Cards With Vision 5 Or Below Can Not Be Used With The Plotter. Version 5.1 Cards Behave As Expected But Does Not Support PML Intructions

 
050000 error

050000 error

The Line Sensor Has Problems Finding The Mark Encoder

 
060000 error

060000 error

The Line Sensor Is Not Functioning Properly Because There Is Too Much Ambient Light

 
060200 error

060200 error

Incompatible Firmware And Carriage PCA

 
060399 error

060399 error

Incompatible Firmware And Line Sensor

 
07xxxx error

07xxxx error

Firmware Error

 
08xxxx error

08xxxx error

PostScript Error

 
080001 error

080001 error

Hard Disk Drive Installed Without PostScript

 
09xxxx error

09xxxx error

Problem With The Hard Disk

 
09004 error

09004 error

PostScript Installed Without The Hard Disk Drive

 
010020 error

010020 error

The CheckSum Read On The Flash SIMM Is Incorrect

 
010021 error

010021 error

The Base DRAM Or The RAM SIMM Tests Failed

 
010022 error

010022 error

The SWATH RAM Test Failed

 
010023 error

010023 error

A Fuse On The Main PCA Has Blown

 
010025 error

010025 error

Problem Initializing The Encoder Pulse Generator

 
010030 error

010030 error

One Of The Two Interconnect Boards Not Detected

 
010031 error

010031 error

The Printhead Primitive Driver ASIC Test Failed

 
010032 error

010032 error

Fan Test Failed – Current Not Detected In One Or Both Fans

 
010033 error

010033 error

The DC Motor ASIC Test Failed

 
010034 error

010034 error

One Of The DC Motor Has Failed

 
010035 error

010035 error

One Of The Stepper Motors Has Failed

 
010036 error

010036 error

ADC Test Failure In The Main PCA

 
010037 error

010037 error

ADC Test Failure In The Carriage PCA

 
010038 error

010038 error

A Printhead Voltage Could Not Be Set – Main PCA Failure

 
010039 error

010039 error

A Printhead Voltage Could Not Be Set – Carriage PCA Failure

 
010040 error

010040 error

The Ambient Temperature Measured Is Out Of The Normal Range

 
010041 error

010041 error

Problem In Setting The Printhead Voltage

 
010042 error

010042 error

The Status Of One Of The Optical Sensors Is Not Stable When It Should Be

 
010100 error

010100 error

Error Reading In The EEROM

 
010101 error

010101 error

An Action Outside The EEROM Limits Has Been Performed

 
010102 error

010102 error

Physical EEROM Write And/Or Write Operations Failed. The EEROM Data That Is Written Does Not Match The Data That Is Read

 
010110 error

010110 error

The Content Of The Permanent Configuration Area Of The EEROM Is Not Valid When The Printer Is initialised In Service Mode

 
010111 error

010111 error

The Content Of The User Configuration Area EEROM Is Not Valid When The Printer Is initialised

 
010120 error

010120 error

The Content Of The Permanent Configuration Area Of The EERom Is Not Valid When Printer Is initialised In Normal Mode

 
010121 error

010121 error

One Of The Banks Of The User Area Was Corrupted While Writing Or Reading In That Area

 
030000 error

030000 error

Error In Finding The Primer Home Position

 
030001 error

030001 error

Error In Finding The Elevator Home Position

 
030002 error

030002 error

Error In Finding The Refill Arm Home Position

 
030003 error

030003 error

Error In Finding The refill Stepper Motor Home Position

 
030004 error

030004 error

Error In Finding The Service Station Home Position

 
030005 error

030005 error

Elevator Has A Problem Reaching A Desired Position

 
030006 error

030006 error

The Refill Position In The Y-axis In Not Calibrated

 
020010 error

020010 error

Problem With Fine Movement of The Y-Axis Motor

 
020011 error

020011 error

Error During Initialization Of The Y-Axis

 
040xxx error

040xxx error

MIO Card Error

 
040601 error

040601 error

The MIO Card Does Not Support The MIO 6 Protocol Cards With Vision 5 Or Below Can Not Be Used With The Plotter. Version 5.1 Cards Behave As Expected But Does Not Support PML Instructions

 
050000 error

050000 error

The Line Sensor Has Problems Finding The Mark Encoder

 
060000 error

060000 error

The Line Sensor Is Not Functioning Properly Because There Is To Much Ambient Light

 
060200 error

060200 error

Incompatible Firmware And Carriage PCA

 
060399 error

060399 error

Incompatible Firmware And Line Sensor

 
07xxxx error

07xxxx error

Firmware Error

 
08xxxx error

08xxxx error

PostScript Error

 
080001 error

080001 error

Hard Disk Drive Installed Without PostScript

 
09xxxx error

09xxxx error

Problem With The Hard Disk

 
09004 error

09004 error

PostScript Installed Without The Hard Disk Drive

 
010020 error

010020 error

The CheckSum Read On The Flash SIMM Is Incorrect

 
010021 error

010021 error

The Base DRAM Or The RAM SIMM Tests Failed

 
010022 error

010022 error

The SWATH RAM Test Failed

 
010023 error

010023 error

A Fuse On The Main PCA Has Blown

 
010025 error

010025 error

Problem Initializing The Encoder Pulse Generator

 
010030 error

010030 error

One Of The Two Interconnect Boards Not Detected

 
010031 error

010031 error

The Printhead Primitive Driver ASIC Test Failed

 
010032 error

010032 error

Fan Test Failed – Current Not Detected In One Or Both Fans

 
010033 error

010033 error

The DC Motor ASIC Test Failed

 
010034 error

010034 error

One Of The DC Motor Has Failed

 
010035 error

010035 error

One Of The Stepper Motors Has Failed

 
010036 error

010036 error

ADC Test Failure In The Main PCA

 
010037 error

010037 error

ADC Test Failure In The Carriage PCA

 
010038 error

010038 error

A Printhead Voltage Could Not Be Set – Main PCA Failure

 
010039 error

010039 error

A Printhead Voltage Could Not Be Set – Carriage PCA Failure

 
010040 error

010040 error

The Ambient Temperature Measured Is Out Of The Normal Range

 
010041 error

010041 error

Problem In Setting The Printhead Voltage

 
010042 error

010042 error

The Status Of One Of The Optical Sensors Is Not Stable When It Should Be

 
010100 error

010100 error

Error Reading In The EEROM

 
010101 error

010101 error

An Action Outside The EEROM Limits Has Been Performed

 
010102 error

010102 error

Physical EEROM Write And/Or Write Operations Failed. The EEROM Data That Is Written Does Not Match The Data That Is Read

 
010110 error

010110 error

The Content Of The Permanent Configuration Area Of The EEROM Is Not Valid When The Printer Is initialised In Service Mode

 
010111 error

010111 error

The Content Of The User Configuration Area EEROM Is Not Valid When The Printer Is initialised

 
010120 error

010120 error

The Content Of The Permanent Configuration Area Of The EERom Is Not Valid When Printer Is initialised In Normal Mode

 
010121 error

010121 error

One Of The Banks Of The User Area Was Corrupted While Writing Or Reading In That Area

 
035000 error

035000 error

Error In Finding The Primer Home Position

 
035001 error

035001 error

Error In Finding The Elevator Home Position

 
035002 error

035002 error

Error In Finding The Refill Arm Home Position

 
035003 error

035003 error

Error In Finding The refill Stepper Motor Home Position

 
035004 error

035004 error

Error In Finding The Service Station Home Position

 
035005 error

035005 error

Elevator Has A Problem Reaching A Desired Position

 
035006 error

035006 error

The Refill Position In The Y-axis is Not Calibrated

 
020010 error

020010 error

Problem With Fine Movement of The Y-Axis Motor

 
020011 error

020011 error

Error During Initialization Of The Y-Axis

 
040xxx error

040xxx error

MIO Card Error

 
040601 error

040601 error

The MIO Card Does Not Support The MIO 6 Protocol Cards With Vision 5 Or Below Can Not Be Used With The Plotter. Version 5.1 Cards Behave As Expected But Does Not Support PML Instructions

 
050000 error

050000 error

The Line Sensor Has Problems Finding The Mark Encoder

 
060000 error

060000 error

The Line Sensor Is Not Functioning Properly Because There Is Too Much Ambient Light

 
060200 error

060200 error

Incompatible Firmware And Carriage PCA

 
060399 error

060399 error

Incompatible Firmware And Line Sensor

 
07xxxx error

07xxxx error

Firmware Error

 
08xxxx error

08xxxx error

PostScript Error

 
080001 error

080001 error

Hard Disk Drive Installed Without PostScript

 
09xxxx error

09xxxx error

Problem With The Hard Disk

 
09004 error

09004 error

PostScript Installed Without The Hard Disk Drive

 
01.0:03 error

01.0:03 error

Error Impact 12C Channel

 
01.0:10 error

01.0:10 error

Problem With The Gamut PCI PCA

 
01.1:10 error

01.1:10 error

Problem With The PrintMech PCA

 
01.2:10 error

01.2:10 error

ISS PCA Faulty – Humidity Sensor Out Of Scale Or NVM Backup Failure

 
02:10 error

02:10 error

Encoder Seems To Be Wrong

 
02.1:10 error

02.1:10 error

Problem With The Carriage PCA

 
03:10 error

03:10 error

Problem With The Power Supply Unit

 
05.1:10 error

05.1:10 error

CPU Fan Is Stopped Or Burnt

 
05.3:10 error

05.3:10 error

Main Memory Size Failure

 
06:03 error

06:03 error

NVM File Has Bad CRC

 
06:10 error

06:10 error

Main NVM Failure – Not Detected, Read/Write Failed Or Readback Error

 
07:10 error

07:10 error

Aerosol Fan Drive Burnt

 
08:10 error

08:10 error

Problem With Front Panel

 
11:10 error

11:10 error

Trailing Cable Does Not Seem To Be Detected

 
13.n:10 error

13.n:10 error

Problem Starting Acumen Supplies

 
21:03 error

21:03 error

Service Station Servo Shutdown

 
21:12 error

21:12 error

Fail Moving Service Station

 
21:13 error

21:13 error

Problem With The Service Station

 
23:10 error

23:10 error

Problem With The APS

 
24:03 error

24:03 error

Ink Setup failure(Ink Supply Tubes Purge Failed)

 
24:10 error

24:10 error

Broken Bag Detected in Ink Cartridge

 
26.0:01 error

26.0:01 error

Bad Contact Detected In ISS Slot 0 Floater

 
26.1:01 error

26.1:01 error

Bad Contact Detected In ISS Slot 1 Floater

 
26.2:01 error

26.2:01 error

Bad Contact Detected In ISS Slot 2 Floater

 
26.3:01 error

26.3:01 error

Bad Contact Detected In ISS Slot 3 Floater

 
26.n:10 error

26.n:10 error

Order Of Ink Supplies Incorrect

 
26:14 error

26:14 error

A Wrong Ink Cartridge Has Been Detected

 
27:03 error

27:03 error

An Error Has Occurred In Printhead Detection

 
27:14 error

27:14 error

A Wrong Printhead Has Been Detected

 
29.0:01 error

29.0:01 error

Printhead Cleaner Not Inserted Correctly In Slot 1

 
29.1:01 error

29.1:01 error

Printhead Cleaner Not Inserted Correctly In Slot 2

 
29.2:01 error

29.2:01 error

Printhead Cleaner Not Inserted Correctly In Slot 3

 
29.3:01 error

29.3:01 error

Printhead Cleaner Not Inserted Correctly In Slot 4

 
29.4:01 error

29.4:01 error

Printhead Cleaner Not Inserted Correctly In Slot 5

 
29.5:01 error

29.5:01 error

Printhead Cleaner Not Inserted Correctly In Slot 6

 
29.6:01 error

29.6:01 error

Printhead Cleaner Not Inserted Correctly In Slot 7

 
29.7:01 error

29.7:01 error

Printhead Cleaner Not Inserted Correctly In Slot 8

 
41:03 error

41:03 error

Electrical Current Limit In Media-Axis Motor

 
41:10 error

41:10 error

Electrical Fault In Media-Axis Motor

 
42:03 error

42:03 error

Elecrtical Current Limit In Scan-Axis Motor

 
42:10 error

42:10 error

Electrical Fault In Scan-Axis Motor

 
43:10 error

43:10 error

Vacuum Fan Has Stopped Functioning

 
44:10 error

44:10 error

Problem With The Aerosol Fan

 
44:11 error

44:11 error

Aerosol Fan Not Connected

 
51:10 error

51:10 error

Window Sensor Failure

 
51.1:10 error

51.1:10 error

PHC Access Door Sensor Failure

 
52:10 error

52:10 error

Drop Detector Switch On/Off Failure

 
53:10 error

53:10 error

Media Sensor Failure

 
54:10 error

54:10 error

Media Lever Sensor failure

 
55:10 error

55:10 error

Problem With The Line Sensor

 
56:03 error

56:03 error

Analog Encoder Calibration Failed

 
56:10 error

56:10 error

Analog Encoder Calibration Failed

 
61:01 error

61:01 error

The File Format Is Incorrect And The Printer Cannot Process The Job

 
61:04.1 error

61:04.1 error

The Postscript Fonts Are Missing. Upgrade The Firmware

 
61:08.1 error

61:08.1 error

The File Cannot Be Printed Because It Is Password Protected

 
63:04 error

63:04 error

Input/Output Problem Through The Network Card

 
64:04 error

64:04 error

Input/Output Problem Through The USB Port

 
65:04 error

65:04 error

Input/Output Problem Through An Unknown Port

 
66:08 error

66:08 error

Cannot Print File On Current Paper Type. The Paper Type Has Changed Since The File Was Sent

 
67:04 error

67:04 error

Input/Output Problem Through a Fireware Port

 
68:03 error

68:03 error

Non-critical permanent data was lost. This does not prevent the printer working, only that internal life counters will not be recorded untill the printer is restarted

 
71:03 error

71:03 error

Out of memory failure

 
71:04 error

71:04 error

Out of memory failure

 
71:19 error

71:19 error

Defult serial Number found in the main and back up NVM. It seems that both the Ink Supply and Hard Disk Drive have been replaced together

 
72:04 error

72:04 error

Generic Firmware error

 
73:03 error

73:03 error

Servo error

 
74:00 error

74:00 error

Failed getting part number/serial number

 
74:01 error

74:01 error

Error uploading firmware

 
74:04 error

74:04 error

Old vacuum fan detected – upgrade the firmware

 
76:03 error

76:03 error

Out of disk space – data was lost

 
77:04 error

77:04 error

Embedded web server internal software error

 
79:03 error

79:03 error

Generic firmware error

 
79:04 error

79:04 error

Generic firmware error

 
79.1:04 error

79.1:04 error

CDS server lost connection with client

 
81:01 error

81:01 error

Paper servo shutdown

 
81:03 error

81:03 error

It was impossible to correctly stop the servo before setting the encoder position

 
81:10 error

81:10 error

Fail starting paper motor

 
85:03 error

85:03 error

Problem finding the drive roller zero

 
86:01 error

86:01 error

Carriage servo shutdown

 
86:03 error

86:03 error

Scan-axis lenght test failure

 
86:10 error

86:10 error

Initialising scan-axis motor failure

 
86:11 error

86:11 error

Scan-axis length too short

 
91:10 error

91:10 error

Repeated printhead issue

 
93:11 error

93:11 error

Unable to pressurise the IDS

 
98:02 error

98:02 error

Switching to lower performance due to printhead quality

 
01.0:03 error

01.0:03 error

Error Impact 12C Channel

 
01.0:10 error

01.0:10 error

Problem With The Gamut PCI PCA

 
01.1:10 error

01.1:10 error

Problem With The PrintMech PCA

 
01.2:10 error

01.2:10 error

ISS PCA Faulty – Humidity Sensor Out Of Scale Or NVM Backup Failure

 
02:10 error

02:10 error

Encoder Seems To Be Wrong

 
02.1:10 error

02.1:10 error

Problem With The Carriage PCA

 
03:10 error

03:10 error

Problem With The Power Supply Unit

 
05.1:10 error

05.1:10 error

CPU Fan Is Stoppede Or Burnt

 
05.3:10 error

05.3:10 error

Main Memory Size Failure

 
06:03 error

06:03 error

NVM File Has Bad CRC

 
06:10 error

06:10 error

Main NVM Failure – Not Detected, Read/Write Failed Or Readback Error

 
07:10 error

07:10 error

Aerosol Fan Drive Burnt

 
08:10 error

08:10 error

Problem With Front Panel

 
11:10 error

11:10 error

Trailing Cable Does Not Seem To Be Detected

 
13.n:10 error

13.n:10 error

Problem Starting Acumen Supplies

 
21:03 error

21:03 error

Service Station Servo Shutdown

 
21:12 error

21:12 error

Fail Moving Service Station

 
21:13 error

21:13 error

Problem With The Service Station

 
23:10 error

23:10 error

Problem With The APS

 
24:03 error

24:03 error

Ink Setup failure (Ink Supply Tubes Purge Failed)

 
24:10 error

24:10 error

Broken Bag Detected in Ink Cartridge

 
26.0:01 error

26.0:01 error

Bad Contact Detected In ISS Slot 0 Floater

 
26.1:01 error

26.1:01 error

Bad Contact Detected In ISS Slot 1 Floater

 
26.2:01 error

26.2:01 error

Bad Contact Detected In ISS Slot 2 Floater

 
26.3:01 error

26.3:01 error

Bad Contact Detected In ISS Slot 3 Floater

 
26.n:10 error

26.n:10 error

Order Of Ink Supplies Incorrect

 
26:14 error

26:14 error

A Wrong Ink Cartridge Has Been Detected

 
27:03 error

27:03 error

An Error Has Occurred In Printhead Detection

 
27:14 error

27:14 error

A Wrong Printhead Has Been Detected

 
29.0:01 error

29.0:01 error

Printhead Cleaner Not Inserted Correctly In Slot 1

 
29.1:01 error

29.1:01 error

Printhead Cleaner Not Inserted Correctly In Slot 2

 
29.2:01 error

29.2:01 error

Printhead Cleaner Not Inserted Correctly In Slot 3

 
29.3:01 error

29.3:01 error

Printhead Cleaner Not Inserted Correctly In Slot 4

 
29.4:01 error

29.4:01 error

Printhead Cleaner Not Inserted Correctly In Slot 5

 
29.5:01 error

29.5:01 error

Printhead Cleaner Not Inserted Correctly In Slot 6

 
29.6:01 error

29.6:01 error

Printhead Cleaner Not Inserted Correctly In Slot 7

 
29.7:01 error

29.7:01 error

Printhead Cleaner Not Inserted Correctly In Slot 8

 
41:03 error

41:03 error

Electrical Current Limit In Media-Axis Motor

 
41:10 error

41:10 error

Electrical Fault In Media-Axis Motor

 
42:03 error

42:03 error

Electrical Current Limit In Scan-Axis Motor

 
42:10 error

42:10 error

Electrical Fault In Scan-Axis Motor

 
43:10 error

43:10 error

Vacuum Fan Has Stopped Functioning

 
44:10 error

44:10 error

Problem With The Aerosol Fan

 
44:11 error

44:11 error

Aerosol Fan Not Connected

 
51:10 error

51:10 error

Window Sensor Failure

 
51.1:10 error

51.1:10 error

PHC Access Door Sensor Failure

 
52:10 error

52:10 error

Drop Detector Switch On/Off Failure

 
53:10 error

53:10 error

Media Sensor Failure

 
54:10 error

54:10 error

Media Lever Sensor failure

 
55:10 error

55:10 error

Problem With The Line Sensor

 
56:03 error

56:03 error

Analog Encoder Calibration Failed

 
56:10 error

56:10 error

Analog Encoder Calibration Failed

 
61:01 error

61:01 error

The File Format Is Incorrect And The Printer Cannot Process The Job

 
61:04.1 error

61:04.1 error

The Postscript Fonts Are Missing. Upgrade The Firmware

 
61:08.1 error

61:08.1 error

The File Cannot Be Printed Because It Is Password Protected

 
63:04 error

63:04 error

Input/Output Problem Through The Network Card

 
64:04 error

64:04 error

Input/Output Problem Through The USB Port

 
65:04 error

65:04 error

Input/Output Problem Through An Unknown Port

 
66:08 error

66:08 error

Cannot Print File On Current Paper Type. The Paper Type Has Changed Since The File Was Sent

 
67:04 error

67:04 error

Input/Output Problem Through a Fireware Port

 
68:03 error

68:03 error

Non-critical permanent data was lost. This does not prevent the printer working, only that internal life counters will not be recorded until the printer is restarted

 
71:03 error

71:03 error

Out of memory failure

 
71:04 error

71:04 error

Out of memory failure

 
71:19 error

71:19 error

Default serial Number found in the main and back up NVM. It seems that both the Ink Supply and Hard Disk Drive have been replaced together

 
72:04 error

72:04 error

Generic Firmware error

 
73:03 error

73:03 error

Servo error

 
74:00 error

74:00 error

Failed getting part number/serial number

 
74:01 error

74:01 error

Error uploading firmware

 
74:04 error

74:04 error

Old vacuum fan detected – upgrade the firmware

 
76:03 error

76:03 error

Out of disk space – data was lost

 
77:04 error

77:04 error

Embedded web server internal software error

 
79:03 error

79:03 error

Generic firmware error

 
79:04 error

79:04 error

Generic firmware error

 
79.1:04 error

79.1:04 error

CDS server lost connection with client

 
81:01 error

81:01 error

Paper servo shutdown

 
81:03 error

81:03 error

It was impossible to correctly stop the servo before setting the encoder position

 
81:10 error

81:10 error

Fail starting paper motor

 
85:03 error

85:03 error

Problem finding the drive roller zero

 
86:01 error

86:01 error

Carriage servo shutdown

 
86:03 error

86:03 error

Scan-axis length test failure

 
86:10 error

86:10 error

Initialising scan-axis motor failure

 
86:11 error

86:11 error

Scan-axis length too short

 
91:10 error

91:10 error

Repeated printhead issue

 
93:11 error

93:11 error

Unable to pressurise the IDS

 
98:02 error

98:02 error

Switching to lower performance due to printhead quality

 
Designjet 5000/5500 ffff ffff xxxxxxxx error

Designjet 5000/5500 ffff ffff xxxxxxxx error

General firmware error

 
ffff ffff 02b301b0 error

ffff ffff 02b301b0 error

This error usually appears at the beginning of Printhead Alignment due to a firmware bug. If requent, upgrade firmware to A.02.xx

 
ffff ffff 01dcxxxx error

ffff ffff 01dcxxxx error

There is a problem with the I/O Card (happens during power up)

 
ffff ffff 030d0170 or 030d0171 error

ffff ffff 030d0170 or 030d0171 error

At power-up, the Printer thinks it is smaller than 42 inches

 
ffff ffff 031609xx error

ffff ffff 031609xx error

This error code only appears if the Main PCA was replaced without removing the media from the printer, because the firmware tries to find the last media information in the EEROM. Since the information cannot be found, this error code is displayed. Remove media and re-boot the printer.

 
ffff ffff 03450097 error

ffff ffff 03450097 error

If the Window is opened during the cutting operation, the Printer hangs and the Carriage suddenly stops. If you press any key on the front panel ffff ffff 03450097 may be displayed. Re-boot the Printer and make sure that the Window is never opened during the cutting operation. Upgrade to any A.02.xx firmware release

 
ffff ffff 036000bd error

ffff ffff 036000bd error

This firmware error code is related to the detection of the Printhead cleaners by the line sensor. It always happens during initialisation, while checking the Printhead Cleaners. In most cases, it is a problem of incorrectly inserted Printhead Cleaners, but it can also be caused by a service station fault.

 
ffff ffff 036e0136 error

ffff ffff 036e0136 error

This is an internal general error code which can appear during the Printhead Alignment process. The chance of this error appearing is less than 0.5% and there is nothing wrong with the printer. Re-boot the printer and error code should not appear again.

 
01002D error (Non-Continuable)

01002D error (Non-Continuable)

The main PCA cannot communicate with the Carriage

 
010023 error (Non-Continuable)

010023 error (Non-Continuable)

EEROM Test failure

 
010030 error 034c095e

010030 error 034c095e

This error code appears when the power supply detects a low spike (e.g. due to a temporary loss of tension). There is nothing wrong with the Printer. Re0boot the printer and error code should not appear again.

 
010040 error

010040 error

Error in Paper-axis Encoder quadrature

 
010041 error

010041 error

Error in Scan-axis Encoder quadrature

 
010042 error

010042 error

Error in Service Station-axis Encoder quadrature

 
010090 error (Continuable)

010090 error (Continuable)

Error in Paper-axis Motor Encoder

 
010091 error (Continuable)

010091 error (Continuable)

Error in Paper-axis Motor Encoder

 
010092 error (Continuable)

010092 error (Continuable)

Mark Encoder position not detected on Drive Roller

 
011000 error

011000 error

NIB Crash. Power printer off and on again using the power switch at the back of the printer

 
040000 error 01E603D9

040000 error 01E603D9

This is an error that is related to the parallel port. It happens normally in new printers and only once (it is unlikely to happen again). Even if the error appears again, there is nothing wrong with the Printer.

 
050000 error (Continuable)

050000 error (Continuable)

Lens has problems reading the Mark Encoder on the Drive Roller

 
050001 error (Continuable)

050001 error (Continuable)

Lens has problems reading the Mark Encoder on the Drive Roller

 
06030C error

06030C error

Bad line sensor

 
06040C error

06040C error

Line sensor not connected correctly

 
0A0000 error

0A0000 error

APS Failure

 
0A0010 error

0A0010 error

APS Failure

 
0A0020 error

0A0020 error

Error in calibrating the APS sensor

 
0A0030 error

0A0030 error

Problem in Depressurizing Air System

 
0A0040 error

0A0040 error

APS Failure

 
0A0050 error (Non-Continuable)

0A0050 error (Non-Continuable)

The printer had detected a leak in the Tubes System (should only appear in printers with the Ink Leak Detector installed)

 
0A0060 error (Non-Continuable)

0A0060 error (Non-Continuable)

The Printer has detected a leak in the Tubes System (should only appear in printers with the Ink Leak Detector installed)

 
0A0070 error (Continuable)

0A0070 error (Continuable)

The Backup EEROM contents stored in the Hard Disk Drive are not consistent with the ones required by the firmware

 
0B0000 error

0B0000 error

Bad Ambient Temperature measured

 
0B0001 error

0B0001 error

Bad humidity read

 
0B0002 error

0B0002 error

Bad IDS pressure read

 
0B0003 error

0B0003 error

ADC0 Internal channels check Failure

 
0B0004 error

0B0004 error

APS Failure

 
0B0005 error

0B0005 error

APS Failure

 
0B0006 error

0B0006 error

The trailing cable has been incorrectly connected

 
0B000X error

0B000X error

Unable to detect Fan (X= 7-Vacuum, 8-Cooling, 9-Aerosol)

 
0B0010 xxxxxxxx error

0B0010 xxxxxxxx error

This firmware error code is related to the detection of the printhead cleaners by the line sensor. It always happens during initialisation, while checking the printhead cleaners. In most cases, it is a problem of incorrectly inserted printhead cleaners, but it can also be caused by the service station.

 
0B000A error

0B000A error

Primer Shutdown Error

 
0B000B error

0B000B error

APS Failure

 
0B000C error

0B000C error

Serial Device ADC test failure

 
0B000D error

0B000D error

24 V source test failure

 
0B000E error

0B000E error

At power-up, the Printer thinks it is smaller than 42 inches.

 
Designjet 5500 0B000F error (Continuable)

Designjet 5500 0B000F error (Continuable)

Only applicable to Designjet 5500 series. Unable to detect the Heater. If this error appears, all settings related to the heater will disappear from the front panel.

 
0C0030 error

0C0030 error

Drop detect failure

 
0C0032 error (Continuable)

0C0032 error (Continuable)

Drop detector not calibrated or the calibration settings have been lost

 
0C0040 error

0C0040 error

Error in Printhead Drop Detection. This error code appears when the Printer detects that the same area of nozzles do not work in different Printheads. The possible causes are either fibres or a piece of paper in the Drop Detector or that the Scan-Axis reference is incorrect

 
0C00FF error

0C00FF error

Print Mask could not be generated. The mask generation algorithm could not generate the print mask. Possible causes are memory corruption, print mode definition incompatible with mask restrictions (if using an external RIP). This cause is not likely to be the Printhead because if it was, the Printhead would be marked as XX21 REPLACE.

 
0C1000 error

0C1000 error

Primer not calibrated or the calibration settings have been lost

 
0C1001 error

0C1001 error

Primer Shutdown Error

 
0D0000 error

0D0000 error

No media profiles available

 
0D0000 033f019C

0D0000 033f019C

No media profiles available

 
0D0002 error (Continuable)

0D0002 error (Continuable)

Insufficient memory to Initialize HPGL2/RTL. The minimum memory required is 96 MB so verify memory installed on the printer.

 
0D0003 xxxxxxxx error (Non-Continuable)

0D0003 xxxxxxxx error (Non-Continuable)

This error usually appears at the beginning of printhead alignment due to a firmware bug. If error appears frequently upgrade to firmware release A.02.xx

 
0D0004 xxxxxxxx error (Non-Continuable)

0D0004 xxxxxxxx error (Non-Continuable)

This is an internal general error code which can appear during the Printhead Alignment process. The chance of this error appearing is less than 0.5% and there is nothing wrong with the Printer. Re-boot the printer and the error code should not appear again

 
0D0005 03180382 error (Non-Continuable)

0D0005 03180382 error (Non-Continuable)

After cutting the media, the Printer cannot deactivate the cutter

 
0FXXXX error (Non-Continuable)

0FXXXX error (Non-Continuable)

A firmware error has occurred

 
0F0200 00b007bc error

0F0200 00b007bc error

This is an error related to an internal crash involving media profiles and memory

 
0F0200 00b007E5 error

0F0200 00b007E5 error

Refer to System Error Code 0F0200 00b007bc

 
0F0200 01E603d2 error

0F0200 01E603d2 error

This is an error that is related to the Parallel Port. It happens normally in New Printers and only once (it is unlikely to appear again). Even if the error appears again, there is nothing wrong with the printer

 
0F0100 03180382 error (Non-Continable)

0F0100 03180382 error (Non-Continable)

After cutting the media, the Printer cannot deactivate the cutter

 
1f500XX error (Boot Failed)

1f500XX error (Boot Failed)

This is an error related to the Hard Disk Drive, either the connections are bad or the Hard Disk Drive or the Main PCA are defective

 
e50000 error

e50000 error

This is an error that is related to the Hard Disk Drive, either the connections are bad or the Hard Disk Drive and/or the Main PCA are defective.

 
01.0:YZ error

01.0:YZ error

HCI queue does not end after 2 seconds – problem with formatter and/or main board

 
01.1:YZ error

01.1:YZ error

NVM backup: not found, read, write or read back error

 
01.2:YZ error

01.2:YZ error

Print mech PCA fault or NVM backup failure

 
02.1:YZ error

02.1:YZ error

Encoder seems to be wrong

 
02.2:YZ error

02.2:YZ error

Problem with the Carriage PCA

 
03:YZ error

03:YZ error

Problem with Power Supply Unit

 
05.1:YZ error

05.1:YZ error

CPU Fan is stopped or burnt

 
06:YZ error

06:YZ error

Main NVM failure – not detected, read/write failed or readback error

 
08:YZ error

08:YZ error

Problem with the Front Panel

 
11:YZ error

11:YZ error

Trailing cable does not seem to be detected

 
21:YZ error

21:YZ error

Fail moving Service Station

 
21.1:YZ error

21.1:YZ error

Service Station servo shutdown

 
22.0:YZ error

22.0:YZ error

ISS left BPSO error. (Supplies 0, 1, 2).

 
22.1:YZ error

22.1:YZ error

ISS left BPS1 error. (Supplies 3, 4, 5).

 
24:YZ error

24:YZ error

Ink Setup failure (Ink Delivery System (IDS) Tubes purge failed).

 
26.n:YZ error

26.n:YZ error

Order of Ink Supplies incorrect

 
27:YZ error

27:YZ error

An error has occurred in Printhead detection

 
29.n:YZ error

29.n:YZ error

An error has occurred in Printhead detection

 
31:YZ error

31:YZ error

An error has been detected with the cutter

 
38:YZ error

38:YZ error

An error has been detected with the Media Output Tray

 
41:YZ error

41:YZ error

Electrical fault or current limit in Media-Axis Motor

 
41.1:YZ error

41.1:YZ error

Electrical fault or current limit in Media-Axis Motor

 
42:YZ error

42:YZ error

Electrical fault or current limit in Scan-Axis Motor

 
44:YZ error

44:YZ error

Fan electrical fault, or not connected

 
45:YZ error

45:YZ error

An error with the Rewinder System has been detected

 
47:YZ error

47:YZ error

Star wheels motor error

 
48:YZ error

48:YZ error

PPS system failure

 
51:YZ error

51:YZ error

Window Sensor failure

 
52:YZ error

52:YZ error

The printer has detected a problem with the Drop Detector

 
55:YZ error

55:YZ error

Problem with the Line Sensor. The printer has detected a failure to access Line Sensor EEPROM.

 
56:YZ error

56:YZ error

Drive roller analog encoder sensor fail or calibration failed

 
58:YZ error

58:YZ error

The Line Sensor of the printer is not functioning correctly. Either the line sensor shutter has failed to open, there is a failure to communicate with the Line Sensor, the Line Sensor is not calibrated correctly, or the firmware is not compatible with the Line Sensor.

 
61:YZ error

61:YZ error

The file format is incorrect and the Printer cannot process the job

 
62:YZ error

62:YZ error

PC Interface

 
63:YZ error

63:YZ error

Input/Output problem through the Network Card

 
64:YZ error

64:YZ error

Input/Output problem through the USB port

 
65:YZ error

65:YZ error

Memory Driver Internal I/O error, I/O Socket Manager Internal I/O error

 
66:YZ error

66:YZ error

Cannot print file on current paper type. The paper type has changed since the file was sent, so the file cannot be printed on the paper type currently loaded.

 
67:YZ error

67:YZ error

Input/Output problem through a Firewire Port

 
68:YZ error

68:YZ error

Loss of engine counters tracking

 
71:YZ error

71:YZ error

Out of memory failure

 
71:19 error

71:19 error

Default Serial Number found in the main and backup NVM. It seems that both the Print Mech PCA and Hard Disk Drive have been replaced together

 
72:YZ error

72:YZ error

Generic Firmware error

 
73:YZ error

73:YZ error

Servo Error

 
74:YZ error

74:YZ error

Error uploading firmware update file

 
74.1:YZ error

74.1:YZ error

Error uploading media profile update file

 
75.1:YZ error

75.1:YZ error

Preventative maintenance Kit #1 counter active (Scan Axis Components, Ink Supply Tubes, Trailing Cable, Carriage)

 
75.2:YZ error

75.2:YZ error

Preventative maintenance Kit #2 counter active

 
75.3:YZ error

75.3:YZ error

Preventative maintenance Kit #3 counter active (Cutter Assembly)

 
75.4:YZ error

75.4:YZ error

Preventative maintenance Kit #4 counter active

 
76:YZ error

76:YZ error

Hard disk drive is full

 
77:YZ error

77:YZ error

Web access application. the web server is not functioning correctly

 
78:YZ error

78:YZ error

Borderless printing not possible. Setting ignore

 
78:1:YZ error

78:1:YZ error

Media settings area missing in media settings file

 
79:YZ error

79:YZ error

Generic Firmware error

 
79.1:YZ error

79.1:YZ error

Recoverable firmware error that does not stop the printing process

 
81:YZ error

81:YZ error

Problem with paper advance

 
81.1:YZ error

81.1:YZ error

Problem finding the Drive Roller zero

 
84:YZ error

84:YZ error

Back tension servo shutdown (roll feeding)

 
85:YZ error

85:YZ error

Problem finding the Drive Roller zero

 
86:YZ error

86:YZ error

Possible paper jam

 
87:YZ error

87:YZ error

Problem finding the Scan-axi encoder reading

 
93:YZ error

93:YZ error

Unable to pressurize the Ink Delivery System

 
94:YZ error

94:YZ error

Colour calibration error

 
94.1:YZ error

94.1:YZ error

Profiling algorithm failed

 
98:YZ error

98:YZ error

Automatic backup print mode enabled

 
01.0:YZ error

01.0:YZ error

Communication with Main PCA failed

 
01.1:YZ error

01.1:YZ error

Error in the Print Mech PCA

 
01.2:YZ error

01.2:YZ error

Failure reading acumen chip of an Ink Supply Station

 
01.3:YZ error

01.3:YZ error

Device I2C acumen Right Ink Supply Station failure

 
02.1:YZ error

02.1:YZ error

Problem with the Carriage PCA

 
03:YZ error

03:YZ error

Problem with Power Supply Unit

 
03.0:10YZ error

03.0:10YZ error

Battery of Real time clock ran down

 
06:YZ error

06:YZ error

Failure reading/writing NVM in Hard disk

 
08:YZ error

08:YZ error

No communication between the Front Panel and the Main PCA.

 
(or front panel is blank)

(or front panel is blank)

 
11:YZ error

11:YZ error

Trailing cable does not seem to be detected

 
21:YZ error

21:YZ error

Fail moving Service Station

 
21.1:YZ error

21.1:YZ error

Fail moving the Primer Motor of the Service Station

 
2x.n:10 error

2x.n:10 error

Ink supply error found during IDS diagnostic test. The n represents the ink supply that is failing. The ink supply furthest to the left is always 0, and then they count up from left to right.

 
22.0:YZ error

22.0:YZ error

Left Ink Supply Station error

 
22.1:YZ error

22.1:YZ error

Left Ink Supply Station error

 
22.2:YZ error

22.2:YZ error

Right Ink Supply Station error

 
22.3:YZ error

22.3:YZ error

Right Ink Supply Station error

 
24:YZ error

24:YZ error

Ink Setup failure (you must bring purgers)

 
31:01 error

31:01 error

An error has been detected with the cutter

 
31:02 error

31:02 error

An error has been detected with the cutter

 
31:03 error

31:03 error

Paper is loaded. While testing the cutter, paper should not be loaded

 
41:03 error

41:03 error

Media-Axis Motor failure (likely due to friction or obstacles in the media path)

 
41:YZ error

41:YZ error

Media-Axis Motor failure (likely due to friction or obstacles in the media path)

 
42:03 error

42:03 error

Scan-Axis Motor failure (likely due to obstacles in the scan axis or electrical fault)

 
42:YZ error

42:YZ error

Scan-Axis Motor failure (likely due to friction or obstacles in the media path)

 
44:YZ error

44:YZ error

Fan electrical fault, or not connected

 
47:03 error

47:03 error

Star wheels motor error

 
47:YZ error

47:YZ error

Star wheels motor error

 
48:YZ error

48:YZ error

PPS system failure

 
51:YZ error

51:YZ error

Window Sensor failure

 
52:10 error

52:10 error

The printer has detected fibers in the Drop Detector

 
55:YZ error

55:YZ error

Problem with the Line Sensor (Tetris). The printer has detected a failure to access Line Sensor EEPROM.

 
56:YZ error

56:YZ error

Drive roller analog encoder sensor fail or calibration failed

 
58:YZ error

58:YZ error

The colour sensor ESP (spectrophotometer) of the printer is not working well. It could be a problem with the spectrophotometer, a communication problem between the spectrophotometer and Carriage PCA or the colour sensor shutter does not open properly

 
61:YZ error

61:YZ error

The file format is incorrect and the Printer cannot process the job

 
Designjet Z 62:YZ error

Designjet Z 62:YZ error

PC interface issue. Power on and off. Get the latest version of the firmware.

 
63:YZ error

63:YZ error

Input/Output problem through the Network interface of the formatter

 
64:YZ error

64:YZ error

Input/Output problem through the USB port

 
65:YZ error

65:YZ error

Memory Driver Internal I/O error, I/O Socket Manager Internal I/O error

 
Designjet Z 66:YZ error

Designjet Z 66:YZ error

Cannot print file on current paper type. The paper type has changed since the file was sent, so the file cannot be printed on the paper type currently loaded

 
Designjet Z 67:YZ error

Designjet Z 67:YZ error

Input/Output problem through a firewire port

 
68:YZ error

68:YZ error

Loss of engine counters tracking

 
71:YZ error

71:YZ error

Out of memory failure

 
71:19 error

71:19 error

Default Serial Number found in the main and backup NVM. It seems that both the Print Mech PCA and Hard Disk Drive have been replaced together

 
Designjet Z 72:YZ error

Designjet Z 72:YZ error

Generic firmware error. Check that the printer has the latest firmware version – if not, update

 
72:YZ error

72:YZ error

A service calibration must be performed. Check the internal error code to see which calibration must be performed. To check the internal error code, press UP and CANCEL together while the error code is displayed

 
Designjet Z 73:YZ error

Designjet Z 73:YZ error

Servo error

 
74:YZ error

74:YZ error

Error uploading firmware update file

 
74.1:YZ error

74.1:YZ error

Error uploading media profile update file

 
Designjet Z 75.1:YZ error

Designjet Z 75.1:YZ error

Preventative maintenance kit #1 counter active (Scan Axis Components, Ink supply tubes, trailing cable, carriage)

 
Designjet Z 75.2:YZ error

Designjet Z 75.2:YZ error

Preventative maintenance kit #2 counter active

 
75.21:YZ error

75.21:YZ error

The spittoons (left spittoon, service station) have reached 80% capacity

 
75.22:YZ error

75.22:YZ error

The spittoons (left spittoon, service station) are full

 
76:YZ error

76:YZ error

Hard disk drive is full

 
77:YZ error

77:YZ error

Web access application. the web server is not functioning correctly

 
Designjet Z 78:YZ error

Designjet Z 78:YZ error

Borderless printing not possible. Setting ignored.

 
78:08 error

78:08 error

The job received can not be printed without borders on this paper

 
78:1:YZ error

78:1:YZ error

Media settings area missing in media settings file

 
79:YZ error

79:YZ error

Generic Firmware error

 
79.1:YZ error

79.1:YZ error

Recoverable firmware error that does not stop the printing process

 
Designjet Z 81:YZ error

Designjet Z 81:YZ error

Problem with paper advance

 
81:YZ error

81:YZ error

This error can occur because the printer has been dropped during transportation, causing structural damage. Before continuing with the 81:YZ troubleshooting, first look for structural damage.

 
Designjet Z 81.1:YZ error

Designjet Z 81.1:YZ error

Problem finding the Drive Roller zero

 
Designjet Z 84:YZ error

Designjet Z 84:YZ error

Back tension servo shutdown (roll feedng)

 
85:YZ error

85:YZ error

Problem finding the Drive Roller zero

 
Designjet Z 86:YZ error

Designjet Z 86:YZ error

Possible paper jam

 
86:01 error

86:01 error

Problem moving the carriage, most likely due to a paper jam

 
87:YZ error

87:YZ error

Problem finding the Scan-axi encoder reading

 
93:YZ error

93:YZ error

Unable to pressurize the Ink Delivery System or the ISS Motor does not move as expected.

 
94:YZ error

94:YZ error

Colour calibration error

 
94.1:YZ error

94.1:YZ error

Profiling algorithm failed

 
98:YZ error

98:YZ error

Automatic backup print mode enabled